CROSS-STANDARD public interest · LED luminaire
China-to-Rwanda LED Luminaire Compliance Gap Matrix
AI-compiled from official public sources — cross-checked by multiple AI models, not human-verified. Informational only; see disclaimer. Public-interest, source-linked comparison of common China LED luminaire documentation against Rwanda Standards Board (RSB) requirements: mandatory Pre-Export Verification of Conformity (PVoC) with a Certificate of Conformity, the S-Mark / import inspection scheme, Rwanda Standards (RS) that adopt IEC 60598 / IEC 62560 / IEC 62471, the national energy-efficiency labelling programme, and RURA radio approval for connected lamps — compared against Chinese GB standards and CCC certification.
Dataset 2026-06-11
Last verified 2026-06-15
11 rows
GAP MATRIX
Compliance Gap Matrix
| Compliance item | Common China baseline | Rwanda (RSB) | Gap / action | Source + verification date |
|---|---|---|---|---|
| Energy Efficiency Labelling — Lighting (Rwanda national energy programme) | China operates a mandatory energy-efficiency labelling and minimum-efficiency regime for LED lamps under GB 30255 (Minimum allowable values of energy efficiency and energy efficiency grades for LED lamps), administered through the China Energy Label (CEL) self-declaration and filing system. Products below the minimum efficiency grade may not be placed on the Chinese market, and the China Energy Label must be affixed. This GB 30255 grade and the China Energy Label are domestic; they are not the Rwandan label and do not by themselves satisfy any Rwandan energy-labelling requirement.GB 30255 — Minimum allowable values of energy efficiency and energy efficiency grades for LED lamps (mandatory) China Energy Label (CEL) — self-declaration and filing system administered by the national energy-efficiency label centre |
Rwanda does not operate the EU Ecodesign Regulation (EU) 2019/2020 minimum-performance regime with an EPREL database. Instead, energy efficiency of lighting is addressed through Rwanda's national energy-efficiency programme and any applicable Rwanda Standard / energy-labelling requirement, supported by RSB and the national energy authorities. The practical obligation is to substantiate efficacy (lm/W) and other declared performance figures with reliable test data (typically IEC 62612-based) within the RSB PVoC programme, and to apply any required energy label or efficiency declaration for the consignment. Confirm with RSB / the importer whether a mandatory energy label currently applies to the specific lamp / luminaire category, since coverage can be category-specific and evolving.Rwanda national energy-efficiency programme — lighting energy labelling / efficiency declaration (scope to be confirmed with RSB) RS / IEC 62612 — performance / efficacy basis for the efficiency claim RSB Pre-Export Verification of Conformity (PVoC) programme — Certificate of Conformity required per consignment |
China has a single, well-defined mandatory energy regime (GB 30255 + China Energy Label). Rwanda does NOT replicate the EU Ecodesign minimum-performance / EPREL structure; its energy treatment runs through the national energy-efficiency programme and applicable RS, so there is no one-to-one EU-equivalent threshold to map against and no EPREL-style central database. The China Energy Label cannot be reused for Rwanda. The exporter should: (1) confirm with RSB / the importer whether a mandatory energy label applies to the specific category; (2) substantiate efficacy with an IEC 62612-based report; and (3) apply any required Rwandan energy label per the current programme rules. State plainly to the importer that the EU Ecodesign minimum-efficacy regime is not in force in Rwanda.[INFORMATIONAL] Rwanda does not run the EU Ecodesign minimum-efficacy / EPREL regime; lighting energy efficiency is handled through the national energy-efficiency programme and applicable RS. China's mandatory GB 30255 grade and China Energy Label are domestic and cannot be reused for Rwanda. Substantiate efficacy with an IEC 62612-based report, confirm category label applicability with RSB, and apply any required Rwandan energy label. | Rwanda Standards Board (RSB)2026-06-15 · reference |
| Marking, Labelling & In-Country Importer (RSB S-Mark / import inspection) | For the Chinese market, marking and labelling of in-scope luminaires and lamps follow the GB 7000 / GB 24906 marking clauses and the CCC mark requirement (CCC logo, factory code) where the product is within CNCA-C10-01 scope, plus the China Energy Label where GB 30255 applies. The responsible party in China is the domestic manufacturer / certificate holder. These marks (CCC, China Energy Label) and the 220 V rating reflect the Chinese domestic regime and are not the Rwandan S-Mark or import-inspection requirement.GB 7000 / GB 24906 — marking and labelling clauses for luminaires and self-ballasted LED lamps CCC mark requirement (CNCA-C10-01) and China Energy Label (GB 30255) where applicable |
Regulated LED products entering Rwanda must carry compliant product marking and may need to bear the RSB S-Mark / pass RSB import inspection, with a Certificate of Conformity issued under the PVoC programme per consignment. Marking should include rated voltage / frequency (matching the 230 V / 50 Hz grid), rated power, manufacturer / brand identification, and any required safety and category markings. A registered in-country importer of record is the responsible party for customs clearance and inspection. Because Rwanda is landlocked, goods route via Mombasa or Dar es Salaam, so the conformity documentation must travel with the consignment to clear transit and the Rwandan border.RSB S-Mark / import inspection scheme for regulated products RSB Pre-Export Verification of Conformity (PVoC) programme — Certificate of Conformity required per consignment RS / IEC 60598-1 & RS / IEC 62560 — product marking requirements (voltage, power, identification) |
Both regimes require product marking, but the marks and responsible-party structure differ. China uses the CCC mark + China Energy Label with a domestic certificate holder; Rwanda uses the RSB S-Mark / import inspection + PVoC Certificate of Conformity with an in-country importer of record. The CCC mark and China Energy Label are not recognised in Rwanda. Rated-voltage marking must be reviewed for the 230 V / 50 Hz grid. There is no EU-style Authorised Representative — the in-country importer carries the border responsibility. Conformity documents must accompany the consignment through the Mombasa / Dar es Salaam transit route.[INFORMATIONAL] Regulated LED products for Rwanda need compliant marking, the RSB S-Mark / import inspection, and a PVoC Certificate of Conformity per consignment, with a registered in-country importer of record. China's CCC mark and China Energy Label are not recognised in Rwanda. Verify rated-voltage marking for 230 V / 50 Hz and ensure conformity documents accompany the consignment via the Mombasa / Dar es Salaam route. | Rwanda Standards Board (RSB)2026-06-15 · reference |
| Electromagnetic Compatibility — Emissions (RS / CISPR 15) | China's equivalent emission standard is GB/T 17743 (Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment), which transposes CISPR 15. EMC requirements form part of CCC assessment for in-scope lighting under the applicable CNCA rules. The Chinese GB/T 17743 report is domestic evidence; under the RSB PVoC route, a CISPR 15-based emission report (often from an ILAC-accredited lab) is normally what the inspection body relies on.GB/T 17743 — Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment (transposes CISPR 15) | EMC emission performance of LED lighting equipment for Rwanda is assessed under the Rwanda Standard adopting CISPR 15 (Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment), within the RSB PVoC programme. The requirement controls radio-frequency disturbance (conducted and radiated emissions) so the product does not interfere with radio reception and other equipment. A Certificate of Conformity per consignment and import inspection apply. For lighting with no intentional radio transmitter, this is the EMC emission element; radio-transmitter approval is handled separately by RURA (see RURA topic).RS / CISPR 15 — Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment (adopted Rwanda Standard) RSB Pre-Export Verification of Conformity (PVoC) programme — Certificate of Conformity required per consignment |
GB/T 17743 and RS / CISPR 15 share the same CISPR 15 base, so emission limits are largely aligned. The gap is the route and report acceptance, not the technical limits: Rwanda requires the RSB PVoC Certificate of Conformity per consignment and import inspection, and does not automatically accept the Chinese CCC EMC evidence. The PVoC body typically relies on a CISPR 15 emission report from an accredited laboratory and may inspect the consignment. Test the product at its Rwandan 230 V / 50 Hz operating condition.[INFORMATIONAL] LED lighting for Rwanda must meet EMC emission limits under RS / CISPR 15 within the RSB PVoC programme, with a Certificate of Conformity per consignment. GB/T 17743 and CISPR 15 are aligned, but Chinese CCC EMC evidence is not automatically accepted; a CISPR 15 report from an accredited lab is typically required. Radio-transmitter approval is handled separately by RURA. | Rwanda Standards Board (RSB)2026-06-15 · reference |
| EMC Immunity (RS / IEC 61547) | China's equivalent immunity standard is GB/T 18595 (General lighting equipment — EMC immunity requirements), which transposes IEC 61547. Immunity forms part of the EMC element of CCC assessment for in-scope lighting under the applicable CNCA rules. The Chinese GB/T 18595 report is domestic evidence; the RSB PVoC route normally relies on an IEC 61547-based immunity report, often from an ILAC-accredited laboratory.GB/T 18595 — General lighting equipment — EMC immunity requirements (transposes IEC 61547) | EMC immunity of LED lighting for Rwanda is assessed under the Rwanda Standard adopting IEC 61547 (Equipment for general lighting purposes — EMC immunity requirements), within the RSB PVoC programme. It defines immunity to electrostatic discharge, radiated and conducted RF fields, fast transients / bursts, surges, voltage dips and interruptions on the 230 V / 50 Hz supply. A Certificate of Conformity per consignment and import inspection apply. Together with the CISPR 15 emission element, this completes the EMC assessment for non-radio LED lighting.RS / IEC 61547 — Equipment for general lighting purposes — EMC immunity requirements (adopted Rwanda Standard) RSB Pre-Export Verification of Conformity (PVoC) programme — Certificate of Conformity required per consignment |
GB/T 18595 and RS / IEC 61547 share the IEC 61547 base, so immunity requirements are largely aligned. The gap is again the route and report acceptance: Rwanda requires the RSB PVoC Certificate of Conformity per consignment and import inspection and does not automatically accept Chinese CCC EMC evidence; the PVoC body typically relies on an IEC 61547 immunity report from an accredited lab. Surge / dip immunity should be evaluated for the 230 V / 50 Hz network the product will operate on.[INFORMATIONAL] LED lighting for Rwanda must meet EMC immunity under RS / IEC 61547 within the RSB PVoC programme, with a Certificate of Conformity per consignment. GB/T 18595 and IEC 61547 are aligned, but Chinese CCC EMC evidence is not automatically accepted; an IEC 61547 immunity report from an accredited lab is typically required, evaluated for the 230 V / 50 Hz supply. | Rwanda Standards Board (RSB)2026-06-15 · reference |
| Photobiological Safety — Blue Light Hazard (RS / IEC 62471) | China's equivalent is GB/T 20145-2006 (Photobiological safety of lamps and lamp systems), which transposes IEC 62471, with related guidance in GB/T 34034 for risk-group application. Photobiological safety / blue-light hazard classification is increasingly referenced in Chinese lighting evaluation. The Chinese GB/T 20145 report is domestic evidence; under the RSB PVoC route, an IEC 62471-based report (often from an ILAC-accredited lab) is normally what the inspection body relies on.GB/T 20145-2006 — Photobiological safety of lamps and lamp systems (transposes IEC 62471) GB/T 34034 — Application guidance for blue-light hazard risk-group classification of lighting products |
Photobiological safety of LED lamps and luminaires for Rwanda is assessed under the Rwanda Standard adopting IEC 62471 (Photobiological safety of lamps and lamp systems), within the RSB PVoC programme where the lighting standard set requires it. IEC 62471 classifies sources into Risk Groups (RG0 exempt, RG1, RG2, RG3) primarily for blue-light hazard and retinal thermal hazard, and informs whether warning marking is needed for higher risk groups. Assessment is part of the product safety evidence package supporting the Certificate of Conformity.RS / IEC 62471 — Photobiological safety of lamps and lamp systems (adopted Rwanda Standard) RSB Pre-Export Verification of Conformity (PVoC) programme — Certificate of Conformity required per consignment |
GB/T 20145 and RS / IEC 62471 share the IEC 62471 base, so the photobiological classification method is aligned. The gap is route and report acceptance: Rwanda relies on the RSB PVoC Certificate of Conformity and does not automatically accept Chinese CCC / GB/T 20145 evidence; an IEC 62471-based report from an accredited lab is normally required where the lighting standard set calls for photobiological assessment. Where the product falls into RG2 or above, confirm any warning-marking expectations with the PVoC inspection body, since exact marking rules can differ from China.[INFORMATIONAL] Photobiological safety for LED lighting into Rwanda is assessed against RS / IEC 62471 where the lighting standard set requires it, as part of the RSB PVoC evidence. GB/T 20145 and IEC 62471 are aligned in method, but Chinese evidence is not automatically accepted; an IEC 62471 report from an accredited lab is typically required. For RG2+ sources, confirm warning-marking expectations with the PVoC body. | Rwanda Standards Board (RSB)2026-06-15 · reference |
| Performance / Photometric Declaration (RS / IEC 62612 — self-ballasted LED lamp performance) | China's equivalent performance standard is GB/T 24908 (Self-ballasted LED lamps for general lighting services — Performance requirements), aligned with IEC 62612, with photometric test methods in the GB/T 9468 / CIE-based family. Performance declarations support Chinese energy-efficiency labelling under GB 30255 (see energy-label topic). The Chinese GB/T 24908 report is domestic evidence; under the RSB PVoC route, an IEC 62612-based performance report (often from an ILAC-accredited lab) is normally relied on.GB/T 24908 — Self-ballasted LED lamps for general lighting services — Performance requirements (aligned with IEC 62612) GB 30255 — Minimum allowable values of energy efficiency and energy efficiency grades for LED lamps (see energy-label topic) |
Performance characteristics of self-ballasted LED lamps for Rwanda — luminous flux, luminous efficacy, colour rendering index (CRI), correlated colour temperature, lumen maintenance / lifetime and power factor — are declared against the Rwanda Standard adopting IEC 62612 (Self-ballasted LED lamps for general lighting services — Performance requirements). Reliable photometric declaration underpins both the safety evidence and the energy-efficiency labelling claim, and the PVoC body may verify declared figures against the IEC 62612 test report when issuing the Certificate of Conformity.RS / IEC 62612 — Self-ballasted LED lamps for general lighting services — Performance requirements (adopted Rwanda Standard) RSB Pre-Export Verification of Conformity (PVoC) programme — Certificate of Conformity required per consignment |
GB/T 24908 and RS / IEC 62612 both derive from IEC 62612, so the performance parameter set is aligned. The gap is route and report acceptance: under the RSB PVoC route, Chinese GB/T 24908 reports are not automatically accepted, and an IEC 62612-based report from an accredited lab is normally required. Declared CRI, efficacy and lumen-maintenance figures should be consistent with the energy-label claim, because the PVoC body may cross-check them. Note Rwanda's energy programme drives the efficacy / labelling side rather than a separate mandatory performance grade in the EU sense.[INFORMATIONAL] Self-ballasted LED lamp performance for Rwanda is declared against RS / IEC 62612, supporting both the PVoC Certificate of Conformity and the energy-label claim. GB/T 24908 and IEC 62612 are aligned, but Chinese reports are not automatically accepted; an IEC 62612 report from an accredited lab is typically required, with declared figures consistent with the energy-label claim. | Rwanda Standards Board (RSB)2026-06-15 · reference |
| Hazardous Substances — No Horizontal RoHS Regime in Rwanda | China operates its own hazardous-substance regime for electrical and electronic products (China RoHS) under the Administrative Measures for the Restriction of the Use of Hazardous Substances in Electrical and Electronic Products, with marking and declaration per the GB/T 26572 limits and SJ/T 11364 marking (the orange e / green circle marks) and the GB 30255-adjacent conformity / catalogue mechanisms. China RoHS covers lead, mercury, cadmium, hexavalent chromium, PBB and PBDE. This China RoHS evidence is a domestic obligation; it is not required by Rwanda and is not a Rwandan market-entry condition.Administrative Measures for the Restriction of the Use of Hazardous Substances in Electrical and Electronic Products (China RoHS) GB/T 26572 — concentration limits; SJ/T 11364 — marking of restricted-substance information |
Rwanda does NOT operate an EU-style horizontal restriction-of-hazardous-substances (RoHS) regime for general electrical and electronic products. There is no Rwandan equivalent that mandates the EU RoHS 2 (Directive 2011/65/EU) restricted-substance list (lead, mercury, cadmium, hexavalent chromium, PBB, PBDE and the four added phthalates) as a market-entry condition for LED lighting. Consequently, there is no local RoHS declaration to map against and no RoHS test report that the RSB PVoC programme requires by default. Substance controls that do apply come indirectly via product safety standards (for example mercury content limits embedded in the relevant IEC lamp standards) and any general chemicals / waste rules, not via a horizontal RoHS list. State this plainly to the importer rather than implying a Rwandan RoHS equivalent exists.No horizontal RoHS-equivalent regulation in force in Rwanda for general electricals (confirmed absence) Substance limits apply only indirectly via RS / IEC product-safety standards (e.g. mercury limits embedded in lamp standards) |
This is an inverse gap: China imposes a hazardous-substance regime (China RoHS, GB/T 26572 / SJ/T 11364), while Rwanda imposes no horizontal RoHS requirement on LED lighting. So a Chinese exporter already holding China RoHS documentation has MORE than Rwanda requires on this axis — there is nothing additional to declare for a Rwandan RoHS, because none exists. Do not fabricate a Rwandan RoHS declaration. The only substance constraints to watch are those embedded in the adopted RS / IEC safety standards (e.g. mercury limits) and any future general chemicals / e-waste rules. If a customer contractually asks for RoHS, that is a private buyer requirement, not a Rwandan regulatory one.[INFORMATIONAL] Rwanda has no horizontal RoHS regime for LED lighting, so there is no Rwandan RoHS declaration to provide and none should be fabricated. China's own China RoHS (GB/T 26572 / SJ/T 11364) is a domestic obligation that exceeds what Rwanda requires on this axis. Watch only substance limits embedded in adopted RS / IEC safety standards; any RoHS request from a buyer is contractual, not regulatory in Rwanda. | Rwanda Standards Board (RSB)2026-06-15 · reference |
| Radio Approval for Connected / Smart Lamps (RURA type approval) | In China, radio transmitters in connected lighting require a Radio Type Approval (formerly SRRC / now administered under the State Radio Regulation framework / MIIT radio-transmission-equipment type approval). Connected products may also fall under CCC and network-access requirements. This Chinese radio approval is a domestic authorization tied to Chinese spectrum allocations; it is not recognised by RURA and does not substitute for a Rwandan radio approval.China Radio Transmission Equipment Type Approval (MIIT / former SRRC) for intentional radio transmitters Network-access licence where applicable for connected products |
LED lamps or luminaires with an intentional radio transmitter (Wi-Fi, Bluetooth, Zigbee or other RF control) need radio type approval / authorization from RURA (Rwanda Utilities Regulatory Authority) in addition to the RSB PVoC safety / EMC route. RURA governs the use of the radio spectrum and the approval of radio equipment placed on the Rwandan market. The radio module's frequency bands, power and conformance (typically against ETSI / IEC-aligned RF standards) must be acceptable to RURA. Non-radio LED lighting does not need RURA approval and is handled solely through the RSB PVoC programme.RURA (Rwanda Utilities Regulatory Authority) — radio equipment type approval / authorization for intentional transmitters RF conformance to ETSI / IEC-aligned radio standards acceptable to RURA (frequency, power, spectrum) |
Both China and Rwanda regulate intentional radio transmitters, but through different authorities and spectrum frameworks: China via MIIT radio type approval; Rwanda via RURA. The Chinese radio approval is not transferable — a separate RURA authorization is required for the radio module, referencing frequency bands and power levels acceptable in Rwanda (which align to regional / ITU Region-1 allocations and may differ from China's). This RURA step is in addition to, not part of, the RSB PVoC safety / EMC route. For non-radio LED lighting this row does not apply.[INFORMATIONAL] Connected / smart LED lamps with a radio transmitter need RURA radio type approval in Rwanda, in addition to the RSB PVoC safety / EMC route. China's MIIT radio type approval is a domestic authorization and is not recognised by RURA. Non-radio LED lighting does not need RURA approval. Confirm acceptable frequency bands and power with RURA for the specific module. | Rwanda Utilities Regulatory Authority (RURA)2026-06-15 · reference |
| Packaging, E-Waste & Battery — No EU-Style Horizontal Regimes | China addresses these through separate domestic mechanisms: the China RoHS regime (GB/T 26572 / SJ/T 11364) for hazardous substances; extended-producer-responsibility and recycling policies for electrical/electronic products and packaging; and GB battery-safety standards plus UN 38.3 for lithium battery transport. These are Chinese domestic obligations and recycling/EPR schemes; they are not the same as, and do not satisfy, any Rwandan environmental requirement, but they also exceed what Rwanda imposes as a market-entry condition on LED lighting.China RoHS (GB/T 26572 / SJ/T 11364) and EPR / recycling policies for electrical-electronic products and packaging GB battery-safety standards; UN 38.3 for lithium battery transport |
Rwanda does NOT operate EU-style horizontal producer-responsibility regimes equivalent to the EU Packaging, WEEE (e-waste) and Battery Regulations as conditions for placing LED lighting on the market. Rwanda does have national environmental and e-waste policy direction (including e-waste management efforts and restrictions on certain single-use plastics), but these are not the same as the EU's product-level RoHS/WEEE/Battery market-entry obligations and do not generate an EU-equivalent declaration for a consignment of LED lamps. Where an LED product contains a battery (e.g. emergency or portable units), handle the battery under product-safety standards and any applicable transport (UN 38.3) and import rules rather than under an EU Battery Regulation analogue. Confirm current environmental / packaging rules with the in-country importer.No EU-equivalent horizontal Packaging / WEEE / Battery producer-responsibility regime as a market-entry condition in Rwanda (confirmed absence) National environmental / e-waste policy and single-use-plastic restrictions apply at a general level, not as a per-consignment product declaration Battery transport handled via UN 38.3 and import rules where a battery is present |
This is again an inverse / absence gap: Rwanda imposes no EU-style Packaging / WEEE / Battery producer-responsibility market-entry obligation on LED lighting, so there is no per-consignment environmental declaration to map against and none should be invented. The exporter's existing Chinese EPR / battery-transport documentation is more than Rwanda requires on this axis. The genuine constraints are practical: comply with general Rwandan environmental / single-use-plastic rules at importer level, and treat any contained battery under product-safety and UN 38.3 transport rules. State the absence of an EU-equivalent regime plainly so the importer is not led to expect one.[INFORMATIONAL] Rwanda imposes no EU-style Packaging / WEEE / Battery producer-responsibility market-entry obligation on LED lighting, so no EU-equivalent environmental declaration is required and none should be fabricated. Comply with general Rwandan environmental / single-use-plastic rules at importer level, and handle any contained battery under product-safety and UN 38.3 transport rules. The exporter's Chinese EPR / battery documentation exceeds what Rwanda requires here. | Rwanda Standards Board (RSB)2026-06-15 · reference |
| Electrical Safety — General Luminaire (RSB PVoC + RS / IEC 60598-1) | China's current general luminaire safety standard is GB/T 7000.1-2023 (Luminaires — Part 1: General requirements and tests), replacing GB 7000.1-2015 from 1 January 2026; the edition change moved the designation from mandatory GB to recommended GB/T. CCC obligations for in-scope residential luminaires remain governed by CNCA rules (CNCA-C10-01) rather than the GB/T designation alone. Both GB 7000.1 and the Rwanda-adopted RS / IEC 60598-1 share a common IEC 60598-1 base, but the conformity-assessment route differs: China uses third-party CCC; Rwanda uses the RSB PVoC / Certificate-of-Conformity route at export and import.GB/T 7000.1-2023 — Luminaires — Part 1: General requirements and tests (replaces GB 7000.1-2015 from 1 January 2026; recommended GB/T designation) CNCA-C10-01 — CCC certification rules for luminaires |
LED luminaires imported into Rwanda are regulated electrical products and are normally assessed under the Rwanda Standards Board (RSB) Pre-Export Verification of Conformity (PVoC) programme, which requires a Certificate of Conformity per consignment before shipment. Safety is judged against the relevant Rwanda Standard (RS), which adopts IEC 60598-1 (Luminaires — Part 1: General requirements and tests) and the applicable IEC 60598-2 particular-requirement parts. The assessment covers protection against electric shock (creepage / clearance, insulation, touch current), thermal endurance, mechanical strength, and terminals. Because Rwanda is landlocked, goods arrive via Mombasa or Dar es Salaam; the S-Mark / import-inspection and Certificate of Conformity must be in place so the consignment clears RSB inspection at entry. Verify the 230 V / 50 Hz rating is within the product marking.RSB Pre-Export Verification of Conformity (PVoC) programme — Certificate of Conformity required per consignment RS / IEC 60598-1 — Luminaires — Part 1: General requirements and tests (adopted Rwanda Standard) RS / IEC 60598-2 series — Luminaires — Part 2: Particular requirements (applicable part by luminaire type) |
Both sides derive from IEC 60598-1, so the technical safety baseline is broadly comparable, but the access route differs: Rwanda requires an RSB PVoC Certificate of Conformity per consignment plus S-Mark / import inspection at entry, whereas China uses domestic third-party CCC. Existing Chinese CCC certificates and GB/T 7000.1 reports are not automatically accepted by RSB — the PVoC body typically relies on IEC 60598-based test reports, often from ILAC-accredited laboratories, and may require its own inspection or testing. Voltage marking must reflect Rwanda's 230 V / 50 Hz grid (50 Hz matches China; nominal voltage differs from China's 220 V), so verify the rated-voltage range and any country-specific marking. There is no EU-style Authorised Representative concept; instead an in-country importer of record handles clearance and inspection.[INFORMATIONAL] LED luminaires entering Rwanda are regulated and require an RSB PVoC Certificate of Conformity per consignment plus S-Mark / import inspection, assessed against RS / IEC 60598-1. Although GB 7000.1 and RS / IEC 60598-1 share an IEC base, Chinese CCC certificates are not automatically accepted; the PVoC route typically relies on IEC-based test reports from accredited labs. Verify the 230 V / 50 Hz rating and appoint an in-country importer of record. | Rwanda Standards Board (RSB)2026-06-15 · reference |
| Self-Ballasted LED Lamp Safety (RS / IEC 62560) | China's equivalent safety standard for self-ballasted LED lamps is GB 24906-2010 / GB 24906 (Self-ballasted LED lamps for general lighting services > 50 V — Safety requirements), aligned with IEC 62560. Such lamps fall within CCC scope for the Chinese market under the applicable CNCA rules. The Chinese CCC certificate and GB 24906 test report are domestic conformity evidence and are not automatically accepted under the RSB PVoC route, which relies on IEC 62560-based reports.GB 24906-2010 — Self-ballasted LED lamps for general lighting services > 50 V — Safety requirements (aligned with IEC 62560) CNCA-C10-01 — CCC certification rules for lighting products |
Self-ballasted LED lamps (retrofit bulbs with integrated control gear, > 50 V) sold into Rwanda are assessed under the Rwanda Standard adopting IEC 62560 (Self-ballasted LED lamps for general lighting services — Safety specifications), within the RSB PVoC programme. The standard covers interchangeability, protection against electric shock, insulation resistance and dielectric strength, mechanical strength of the cap, torque, and resistance to heat and fire. A Certificate of Conformity per consignment and S-Mark / import inspection apply as for luminaires. The lamp cap and rated voltage must suit the Rwandan 230 V / 50 Hz supply.RS / IEC 62560 — Self-ballasted LED lamps for general lighting services > 50 V — Safety specifications (adopted Rwanda Standard) RSB Pre-Export Verification of Conformity (PVoC) programme — Certificate of Conformity required per consignment |
GB 24906 and RS / IEC 62560 are both based on IEC 62560, so the safety content is largely aligned. The practical gap is the access route and report acceptance: Rwanda requires the RSB PVoC Certificate of Conformity per consignment and S-Mark / import inspection, and does not automatically accept Chinese CCC certificates. The PVoC body normally requires an IEC 62560 test report, often from an ILAC-accredited laboratory, and may inspect or re-test the consignment. Lamp caps and rated voltage must suit 230 V / 50 Hz. An in-country importer of record (not an EU-style authorised representative) handles clearance.[INFORMATIONAL] Self-ballasted LED lamps for Rwanda are assessed against RS / IEC 62560 within the RSB PVoC programme, requiring a Certificate of Conformity per consignment and S-Mark / import inspection. GB 24906 and IEC 62560 are aligned in content, but Chinese CCC certificates are not automatically accepted; an IEC 62560 report from an accredited lab is typically required. Confirm cap type and 230 V / 50 Hz rating. | Rwanda Standards Board (RSB)2026-06-15 · reference |
E-E-A-T
Named editorial review
Pending named reviewer
Official regulator, standards body, notified body, customs, or primary legal source preferred. Local PDFs are not accepted.
Editorial controlsRows must include publisher, official URL, access date, verification flag, and last_verified before human_reviewed can be true.
SOURCES
Official-source register.
- Rwanda Standards Board (RSB) · accessed 2026-06-15 · reference · used in 10 rows
- Rwanda Utilities Regulatory Authority (RURA) · accessed 2026-06-15 · reference · used in 1 rows