CROSS-STANDARD public interest · LED luminaire
China-to-Philippines LED Luminaire Compliance Gap Matrix
AI-compiled from official public sources — cross-checked by multiple AI models, not human-verified. Informational only; see disclaimer. Public-interest, source-linked comparison of common China LED luminaire documentation against Philippine market-access requirements: the BPS Import Commodity Clearance (ICC) and PS mark under the lighting technical regulation, PNS IEC 60598 / 62560 / 62471 standards, DOE energy labelling and MEPS, NTC type approval for smart lighting, and restricted-substance / e-waste obligations — versus Chinese GB standards and CCC certification. Note the Philippine grid is 230 V 60 Hz, differing from China 220/380 V 50 Hz.
Dataset 2026-06-11
Last verified 2026-06-15
11 rows
GAP MATRIX
Compliance Gap Matrix
| Compliance item | Common China baseline | Philippines (BPS / DTI) | Gap / action | Source + verification date |
|---|---|---|---|---|
| DOE Energy Performance and MEPS for Lighting (Energy Efficiency and Conservation Act / DOE labelling) | China's equivalent is GB 30255-2019 (Energy efficiency requirements for LED room luminaires), which sets three energy efficiency grades: Grade 1 (highest) approx. greater than or equal to 90 lm/W, Grade 2 approx. greater than or equal to 80 lm/W, Grade 3 approx. greater than or equal to 70 lm/W, with Grade 3 the minimum for China market entry. The China Energy Label (CEL) is mandatory for GB 30255-covered products and is registered with CQC / CECP and administered by SAMR. Chinese energy figures are declared for the 220 V 50 Hz supply. The China Energy Label and the Philippine DOE energy label are separate, non-mutual schemes.GB 30255-2019 — Energy efficiency requirements for LED room luminaires (SAC/SAMR) China Energy Label (CEL) scheme — administered by SAMR / CQC / CECP |
In the Philippines, the Department of Energy (DOE) administers minimum energy performance and energy labelling for lighting products under the Energy Efficiency and Conservation Act (Republic Act No. 11285) and its implementing rules, building on the earlier Philippine Energy Labeling Program. Self-ballasted LED lamps and certain LED luminaires must carry the yellow Philippine Energy Label declaring luminous efficacy (lm/W), wattage, luminous flux, correlated colour temperature, and rated life, and must meet the applicable Minimum Energy Performance Standard (MEPS) where one is set for the product class. Performance is tested to the relevant PNS IEC photometric and performance standards (e.g. PNS IEC 62612 for self-ballasted LED lamps). Products below the MEPS floor or without a valid energy label cannot be lawfully distributed. Note: rated voltage/frequency is the Philippine 230 V 60 Hz supply, so photometric and energy figures must be declared for 230 V 60 Hz operation.Republic Act No. 11285 — Energy Efficiency and Conservation Act (DOE energy labelling and MEPS framework) Philippine Energy Labeling Program (PELP) — DOE energy label for lighting products PNS IEC 62612 — Self-ballasted LED lamps for general lighting services — Performance requirements (as adopted in the Philippines) |
The Philippine DOE energy label and any applicable MEPS are a separate pre-market obligation with no mutual recognition of the China Energy Label — a product must be tested and the yellow DOE label declared for the Philippine market regardless of its China grade. Because Philippine ratings are referenced to 230 V 60 Hz while China figures are referenced to 220 V 50 Hz, luminous efficacy, power, and flux must be re-declared (and may differ) under Philippine supply conditions. Manufacturers achieving only China Grade 3 (approx. 70 lm/W) should confirm whether the product clears the applicable Philippine MEPS floor for its class. Performance test reports must be to the PNS-adopted IEC performance standard (e.g. PNS IEC 62612), and the energy label artwork and declared values must follow the DOE format rather than the China CEL format.[INFORMATIONAL] LED lamps and luminaires for the Philippine market generally require a DOE energy label and, where a MEPS is set for the product class, must meet that minimum under RA 11285 and the Philippine Energy Labeling Program. The China Energy Label does not substitute for the DOE label, and energy/photometric values must be declared for the 230 V 60 Hz Philippine supply rather than China 220 V 50 Hz. Confirm the current MEPS floor and the applicable PNS IEC performance standard (e.g. PNS IEC 62612) for the specific product class before market entry. | Department of Energy (DOE), Republic of the Philippines2026-06-15 · reference |
| 230 V 60 Hz Grid Design and Voltage/Frequency Compatibility vs China 220/380 V 50 Hz | China's domestic supply is 220 V 50 Hz single phase (380 V 50 Hz three phase for larger loads), and Chinese luminaires, drivers, and their GB-standard test reports (e.g. GB 19510.14 for LED control gear, GB/T 7000.1 for luminaires) are validated at 220 V 50 Hz. A China-spec rating plate and CCC documentation reflect 220 V 50 Hz operation. Although many wide-input LED drivers (e.g. 100 to 240 V, 50/60 Hz) physically tolerate the Philippine supply, the declared ratings, test reports, and energy figures are referenced to the Chinese supply unless re-declared.GB/T 7000.1 — Luminaires — Part 1: General requirements and tests (China, 220 V 50 Hz reference) GB 19510.14-2014 — Control gear for lamps — Particular requirements for electronic controlgear for LED modules (China) |
The Philippine low-voltage distribution supply is nominally 230 V at 60 Hz (single phase), differing from China's 220 V 50 Hz single phase and 380 V 50 Hz three phase. LED luminaires and their drivers placed on the Philippine market must be rated and verified for 230 V 60 Hz operation: the driver input voltage range must cover the Philippine nominal and its tolerance band, and performance, thermal behaviour, flicker, and any frequency-sensitive control circuitry must be validated at 60 Hz. The rating plate must declare the Philippine voltage/frequency, and DOE energy-label and PNS performance figures must reflect 230 V 60 Hz operation. Plug/socket and wiring practice also follows Philippine conventions rather than Chinese ones.Philippine Electrical Code (PEC) — installation and supply conventions (230 V, 60 Hz nominal) PNS IEC 60598-1 — Luminaires — Part 1: General requirements and tests (rated voltage/frequency declaration, as adopted in the Philippines) |
The Philippine 230 V 60 Hz supply differs from China 220/380 V 50 Hz in both voltage and frequency. Even where a wide-input driver physically operates on both, the Philippine rating plate, ICC/PS test reports, DOE energy label, and PNS performance figures must be declared and verified for 230 V 60 Hz — China 220 V 50 Hz test reports are not directly transferable. Frequency-sensitive items (e.g. some flicker / control behaviour, any 50 Hz-tuned magnetic components) should be re-validated at 60 Hz. Manufacturers should confirm the driver input window covers the Philippine nominal plus tolerance, declare the correct voltage/frequency on the rating plate, and ensure photometric and energy figures used for the DOE label and PNS reports correspond to 230 V 60 Hz operation. Plug, terminal, and installation conventions follow the Philippine Electrical Code rather than Chinese practice.[INFORMATIONAL] The Philippine grid is 230 V 60 Hz, differing from China 220/380 V 50 Hz in both voltage and frequency. LED luminaires and drivers for the Philippines must be rated, tested, and labelled for 230 V 60 Hz: a wide-input driver may physically work on both grids, but the rating plate, ICC/PS test reports, DOE energy label, and PNS performance figures must correspond to Philippine supply conditions and cannot simply reuse China 220 V 50 Hz documentation. Re-validate frequency-sensitive behaviour at 60 Hz before market entry. | Department of Energy (DOE), Republic of the Philippines2026-06-15 · reference |
| Lighting EMC / Radio Disturbance — PNS CISPR 15 within BPS ICC Conformity | China's equivalent is GB 17743-2017 (Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment), technically aligned with CISPR 15. For luminaires sold in China, GB 17743 compliance is part of CCC certification (covering both safety and EMC for relevant categories), tested at CNAS / CMA-accredited laboratories. Chinese CCC EMC test reports are not automatically accepted in the Philippine BPS conformity scheme and may need to be reissued or re-tested by a BPS-recognised laboratory.GB 17743-2017 — Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment (SAC/SAMR, aligned with CISPR 15) | Electromagnetic compatibility for lighting equipment in the Philippines is addressed through the Philippine National Standards adoption of CISPR 15 (PNS CISPR 15 / PNS IEC CISPR 15 — limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment), assessed as part of the BPS conformity scheme for products under the lighting technical regulation where EMC is within scope. Emission limits cover conducted disturbance on the mains terminals (150 kHz to 30 MHz) and radiated disturbance. Test reports must be from a laboratory recognised by BPS (typically ILAC MRA / ISO IEC 17025 accredited). EMC evidence forms part of the technical documentation supporting the Import Commodity Clearance (ICC) or PS licence. Where EMC is not separately mandated for a given lamp type, BPS still expects the product not to cause harmful interference.PNS CISPR 15 / PNS IEC CISPR 15 — Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment (as adopted by BPS) BPS conformity scheme (ICC / PS) under the applicable lighting technical regulation — EMC within scope where mandated |
PNS CISPR 15 and GB 17743 are both derived from CISPR 15, so emission limits are largely harmonized and the underlying test data is often transferable in substance. The practical gaps are procedural: (1) EMC evidence must support the Philippine BPS ICC / PS file, and the test report must come from a BPS-recognised (typically ILAC MRA / ISO IEC 17025) laboratory — a China CCC EMC report may need to be re-issued or supplemented; (2) emissions must be demonstrated under 230 V 60 Hz supply conditions, not the China 220 V 50 Hz basis; (3) the conformity route (ICC per-shipment versus PS licence) determines how often EMC evidence is presented. Confirm with BPS whether EMC is separately required for the specific lamp/luminaire type or assessed only as part of the broader safety conformity.[INFORMATIONAL] Lighting EMC in the Philippines is addressed through PNS CISPR 15 within the BPS ICC / PS conformity scheme where EMC is in scope for the product type. Limits are broadly harmonized with China GB 17743 (both CISPR 15-derived), but the test report must support the Philippine BPS file from a BPS-recognised laboratory and reflect 230 V 60 Hz supply, so a China CCC EMC report may need re-issuance or re-testing. Confirm with BPS whether EMC is separately mandated for the specific lamp/luminaire type. | Bureau of Philippine Standards (BPS), Department of Trade and Industry (DTI)2026-06-15 · reference |
| NTC Type Approval / Type Acceptance for Smart (Wireless) LED Luminaires | In China, a smart luminaire with wireless functionality requires SRRC (State Radio Regulation of China) type approval / radio transmission equipment type approval before sale, covering frequency, bandwidth, and power. SRRC approval is separate from CCC. SRRC and the Philippine NTC are different national radio regulators with no mutual recognition — an SRRC approval does not authorise the device for use in the Philippines.SRRC type approval — radio transmission equipment type approval (China, MIIT/SRRC) | Smart LED luminaires with built-in radio functions (Wi-Fi, Bluetooth, Zigbee, or other RF) are radio-communications equipment under Philippine law and require type approval or type acceptance from the National Telecommunications Commission (NTC) before import, sale, or use. The applicant (usually the in-country importer) submits the radio test report, frequency and power particulars, and equipment details; the device must operate within NTC-authorised frequency bands and power limits. Short-range devices in licence-exempt bands still require NTC registration/type acceptance. This is in addition to the BPS ICC / PS safety clearance and the DOE energy label — the radio module triggers a separate regulator. Test reports are typically to the relevant IEC / ETSI / FCC-equivalent RF standards recognised by NTC.National Telecommunications Commission (NTC) type approval / type acceptance — radio equipment authorisation (Philippines) NTC Memorandum Circulars on short-range devices and type approval of radio communications equipment |
A smart LED luminaire triggers a second Philippine regulator (NTC) that has no China analogue beyond SRRC, and SRRC and NTC do not recognise each other. Chinese manufacturers exporting smart luminaires must: (1) ensure the radio module operates within NTC-authorised bands and power limits — Chinese band/power settings tuned for China regulation may not match the Philippine allocation; (2) obtain NTC type approval / type acceptance via the in-country importer before import or sale; (3) supply RF test reports to NTC-recognised standards (the SRRC report alone is not accepted). This is in addition to BPS ICC / PS safety and the DOE energy label. Selling a wireless luminaire without NTC authorisation is an offence even if BPS and DOE requirements are met.[INFORMATIONAL] Smart LED luminaires with Wi-Fi / Bluetooth / other radio functions require NTC type approval / type acceptance in the Philippines, separate from and in addition to the BPS ICC / PS safety clearance and the DOE energy label. China SRRC approval does not transfer — SRRC and NTC are independent regulators. Verify that the radio module operates within NTC-authorised bands and power limits and obtain NTC authorisation via the in-country importer before import or sale. | National Telecommunications Commission (NTC), Republic of the Philippines2026-06-15 · reference |
| Photobiological Safety — Blue Light Hazard (PNS IEC 62471 Risk Groups) | China has adopted GB/T 20145-2006 (Photobiological safety of lamps and lamp systems), technically equivalent to IEC 62471:2006. GB/T 20145 is a recommended standard (T = tuijian, recommended) and is not universally mandatory for all LED luminaires in the Chinese market; enforcement for residential luminaires is less prescriptive. Both PNS IEC 62471 and GB/T 20145 share the IEC 62471 technical base, so risk-group classification methods are aligned, but China test reports are not automatically accepted in the Philippine BPS conformity file.GB/T 20145-2006 — Photobiological safety of lamps and lamp systems (SAC/SAMR — recommended standard, aligned with IEC 62471:2006) | Photobiological safety of LED lamps and luminaires in the Philippines is assessed using the Philippine National Standard adoption of IEC 62471 (PNS IEC 62471 — Photobiological safety of lamps and lamp systems), which classifies products into risk groups from RG0 (Exempt, no hazard) to RG3 (High risk) based on blue-light-weighted radiance and irradiance. Where photobiological safety is within the scope of the lighting technical regulation, a risk-group assessment supports the BPS ICC / PS technical file, and RG2 / RG3 products carry usage restrictions and warning requirements. The classification is part of the broader product safety demonstration alongside the general luminaire safety standard (PNS IEC 60598) and self-ballasted lamp standard (PNS IEC 62560). Testing should be referenced to the Philippine 230 V 60 Hz operating condition.PNS IEC 62471 — Photobiological safety of lamps and lamp systems (risk group classification, as adopted by BPS) BPS conformity scheme (ICC / PS) under the lighting technical regulation — photobiological safety within scope where mandated |
Both markets use the IEC 62471 risk-group method, so the technical classification is broadly comparable. The gaps are procedural and enforcement-related: (1) where photobiological safety is in scope of the Philippine lighting technical regulation, the risk-group assessment must support the BPS ICC / PS file, and the report should come from a BPS-recognised (ILAC MRA / ISO IEC 17025) laboratory — China GB/T 20145 reports are not automatically accepted; (2) GB/T 20145 is recommended-only in China and may not have been tested for a China-spec product, so a Philippine-bound product may need a fresh RG assessment; (3) RG2 / RG3 products require warning labels and usage instructions in the Philippine file. Most general LED luminaires fall in RG0 or RG1, but the classification must still be documented to support market access.[INFORMATIONAL] Photobiological risk-group classification in the Philippines uses PNS IEC 62471 and supports the BPS ICC / PS technical file where photobiological safety is in scope for the product type. The method is broadly comparable to China GB/T 20145 (both IEC 62471-based), but GB/T 20145 is recommended-only in China and its reports are not automatically accepted by BPS, so a fresh risk-group assessment from a BPS-recognised laboratory may be needed. Document the risk group; RG2 / RG3 products require warning labelling and usage restrictions. | Bureau of Philippine Standards (BPS), Department of Trade and Industry (DTI)2026-06-15 · reference |
| Risk-Group Marking and Consumer Warnings on Label vs China Practice | China's GB 30255 / China Energy Label does not include a blue-light-hazard class, and GB/T 20145 (recommended) does not impose a mandatory consumer-facing risk-group warning for general residential LED luminaires. China product safety marking under GB/T 7000.1 covers general luminaire markings (ratings, symbols, manufacturer information) but does not mandate a photobiological caution label for typical RG0 / RG1 products. There is no China requirement equivalent to a standardised blue-light class on a label.GB 30255-2019 — Energy efficiency requirements for LED room luminaires (SAC/SAMR — no blue light class) GB/T 7000.1 — Luminaires — Part 1: General requirements and tests (general marking requirements) |
Where a luminaire is classified RG2 (Moderate risk) or above under PNS IEC 62471, the Philippine conformity framework expects the risk group and an appropriate caution / warning to be communicated to the user, typically on the product, packaging, or instruction sheet (for example a do-not-stare caution for RG2 sources). The general product safety standards (PNS IEC 60598 for luminaires, PNS IEC 62560 for self-ballasted LED lamps) also carry marking and instruction requirements that the product must satisfy for BPS ICC / PS clearance. Unlike the EU, the Philippines does not mandate a blue-light-hazard class on a standardised energy label; the warning is delivered through product safety marking and instructions rather than a labelling-regulation field. Markings and instructions for the Philippine market are expected in line with local language and regulatory practice.PNS IEC 62471 — Photobiological safety of lamps and lamp systems (risk-group caution / marking guidance) PNS IEC 60598-1 / PNS IEC 62560 — luminaire and self-ballasted lamp marking and instruction requirements (as adopted by BPS) |
Unlike the EU energy label, the Philippines does not have a standardised blue-light-hazard class field on its energy label, but RG2 / RG3 products under PNS IEC 62471 still require an appropriate caution / warning to the user via product safety marking and instructions, which China does not mandate for typical residential luminaires. Chinese manufacturers should: (1) determine the risk group via PNS IEC 62471 testing; (2) for RG2 and above, add the appropriate caution and usage instruction to the product, packaging, or instruction sheet for the Philippine market; (3) ensure general luminaire / lamp markings meet PNS IEC 60598 / 62560 requirements, including any Philippine-specific marking and instruction-language expectations. For RG0 / RG1 products no special consumer caution is generally needed, but the classification should still be documented in the BPS file.[INFORMATIONAL] The Philippines does not mandate a standardised blue-light-hazard class on an energy label as the EU does, but RG2 and above products under PNS IEC 62471 still require an appropriate user caution via product safety marking and instructions, which China does not mandate for typical residential luminaires. Determine the risk group via PNS IEC 62471, add the required caution for RG2 / RG3 products, and ensure marking meets PNS IEC 60598 / 62560 for the Philippine market. | Bureau of Philippine Standards (BPS), Department of Trade and Industry (DTI)2026-06-15 · reference |
| Restricted Substances — No Horizontal RoHS in the Philippines; Chemical Control Instruments Instead | China's equivalent is GB/T 26572-2011 (Requirements for concentration limits for certain restricted substances in electrical and electronic products), covering the original six RoHS substances (Pb, Hg, Cd, Cr(VI), PBB, PBDE) with the same concentration thresholds as EU RoHS, together with China RoHS 2 (Management Measures, SJ/T 11364-2014) requiring a hazardous-substance disclosure label (orange/green) on EEE sold in China. China RoHS 2 is a per-product homogeneous-material disclosure-and-restriction regime — structurally different from the Philippine chemical-management approach, which controls substances at the chemical / import level rather than via a fixed EEE concentration table.GB/T 26572-2011 — Requirements for concentration limits for certain restricted substances in EEE (SAC/SAMR — six substances) SJ/T 11364-2014 — Marking for the restricted use of hazardous substances in electronic and electrical products (China RoHS 2 disclosure label) |
The Philippines does not have a single horizontal RoHS-style directive that restricts a fixed list of hazardous substances across all electrical and electronic equipment in the way the EU RoHS Directive does. Instead, hazardous-substance control is delivered through general chemical-management law: Republic Act No. 6969 (Toxic Substances and Hazardous and Nuclear Wastes Control Act of 1990) and its implementing rules, administered by the Department of Environment and Natural Resources (DENR) through the Environmental Management Bureau (EMB), with the Priority Chemicals List (PCL) and Chemical Control Orders (CCOs) for specific substances such as mercury, lead, cadmium, and certain brominated compounds. Mercury, lead, and cadmium relevant to lighting are subject to CCOs / PCL controls rather than a per-product homogeneous-material concentration limit. Importers must ensure their products and components comply with any applicable CCO and PCL obligations and with import controls under RA 6969.Republic Act No. 6969 — Toxic Substances and Hazardous and Nuclear Wastes Control Act of 1990 (DENR / EMB) DENR Priority Chemicals List (PCL) and Chemical Control Orders (CCOs) — e.g. for mercury, lead, cadmium, certain brominated compounds |
There is no Philippine horizontal RoHS directive, so a Chinese exporter cannot rely on either an EU-RoHS or a China-RoHS declaration to satisfy a single Philippine equivalent — there is none. Instead the gap is one of regime structure: (1) the manufacturer must screen for substances controlled under RA 6969 CCOs / PCL (notably mercury, lead, cadmium and certain brominated compounds relevant to LED components and solders) and ensure compliance with those chemical-level controls and import requirements; (2) China RoHS 2 disclosure labelling does not satisfy Philippine chemical-control obligations, and conversely the Philippines does not require the China-style orange/green disclosure label; (3) buyers and supply chains increasingly expect EU-RoHS-style substance declarations as a commercial norm even where not legally mandated. Manufacturers should treat restricted-substance compliance as substance/import-driven (RA 6969) rather than as a single product RoHS certificate, and verify which CCOs apply to their bill of materials.[INFORMATIONAL] The Philippines has no horizontal RoHS directive — there is no single Philippine equivalent that an EU-RoHS or China-RoHS declaration satisfies. Hazardous-substance control is delivered through RA 6969 Chemical Control Orders and the Priority Chemicals List (mercury, lead, cadmium, certain brominated compounds), administered by DENR / EMB at the chemical and import level. Chinese exporters should screen their bill of materials against applicable CCOs / PCL rather than rely on a product RoHS certificate, and note that China RoHS 2 disclosure labelling does not satisfy Philippine obligations. | Environmental Management Bureau (EMB), Department of Environment and Natural Resources (DENR), Philippines2026-06-15 · reference |
| E-Waste and End-of-Life — Hazardous Waste Handling for LED Products (RA 6969 / EMB) | China's WEEE-equivalent framework is the Regulation on the Administration of the Recovery and Disposal of Waste Electrical and Electronic Products (State Council Order No. 551) and the associated WEEE catalogue, with a fund-based extended-producer-responsibility mechanism for listed product categories administered by environmental authorities. Producers of listed EEE pay into a WEEE treatment fund. The Chinese WEEE regime and the Philippine hazardous-waste / nascent EPR framework are separate; compliance in China does not satisfy Philippine end-of-life obligations.State Council Order No. 551 — Regulation on the Administration of the Recovery and Disposal of Waste Electrical and Electronic Products (China WEEE) and WEEE catalogue | In the Philippines, waste electrical and electronic equipment (WEEE), including end-of-life LED lamps and luminaires that contain or are contaminated with hazardous components, is regulated as hazardous waste under Republic Act No. 6969 and its implementing rules and the DENR / EMB hazardous-waste management framework (registration of generators, accredited transporters and treatment-storage-disposal facilities, and a manifest system). There is no single EU-WEEE-style extended-producer-responsibility (EPR) directive specific to lighting nationwide, but DENR guidance on WEEE and hazardous-waste handling applies, and the broader Extended Producer Responsibility Act (RA 11898, focused primarily on plastic packaging) signals a direction toward producer responsibility. Importers and distributors should plan for compliant disposal channels and any take-back expectations, and ensure mercury-containing or lead-bearing components are handled under the hazardous-waste rules.Republic Act No. 6969 — Toxic Substances and Hazardous and Nuclear Wastes Control Act of 1990 (hazardous-waste / WEEE handling, DENR / EMB) Republic Act No. 11898 — Extended Producer Responsibility Act of 2022 (producer responsibility, primarily plastic packaging; signals EPR direction) |
The Philippines handles end-of-life LED products primarily through hazardous-waste rules under RA 6969 rather than a dedicated lighting WEEE / EPR directive, while China uses a fund-based WEEE catalogue mechanism — the two are not equivalent and neither registration transfers. For the Philippine market, the exporter and its in-country importer should: (1) confirm whether the product or its end-of-life handling triggers hazardous-waste obligations (especially for any mercury-, lead-, or brominated-flame-retardant-bearing components); (2) plan for compliant disposal via DENR-accredited channels; (3) monitor the developing EPR landscape (RA 11898) for any future obligations extending to electronics/lighting. China WEEE fund payment does not discharge Philippine obligations, and Philippine importers may face the practical end-of-life burden domestically.[INFORMATIONAL] The Philippines regulates end-of-life LED products mainly through RA 6969 hazardous-waste rules (DENR / EMB) rather than a dedicated lighting WEEE / EPR directive, with the EPR Act (RA 11898) signalling a future direction. This differs from China's fund-based WEEE catalogue mechanism, and neither registration transfers. Exporters and their in-country importers should plan for compliant disposal of hazardous components (mercury, lead, brominated flame retardants) via DENR-accredited channels and monitor developing EPR obligations. | Environmental Management Bureau (EMB), Department of Environment and Natural Resources (DENR), Philippines2026-06-15 · reference |
| BPS ICC vs PS Mark and In-Country Importer of Record vs CCC / CQC | In China, the primary mandatory certification for luminaires sold in the residential market is CCC (China Compulsory Certification), administered by CNCA and certified by CNCA-authorised bodies such as CQC (China Quality Certification Centre); voluntary CQC certification exists for products outside mandatory CCC. CCC is a manufacturer/product certification held directly by the producer, with factory inspection and ongoing surveillance. The Chinese CCC scheme and the Philippine BPS ICC / PS scheme are separate and non-mutual: CCC does not authorise import into the Philippines, and the Philippine clearance must be held by an in-country importer (ICC) or local manufacturer (PS), which is a different applicant model from China's direct-manufacturer CCC certificate.CNCA-C10-01 — CCC certification rules for luminaires (CNCA / CQC) SRRC type approval — required separately for wireless-enabled luminaires in China |
For LED lamps and luminaires covered by the Philippine lighting technical regulation, market access runs through the Bureau of Philippine Standards (BPS) under the DTI: imported products obtain an Import Commodity Clearance (ICC) per importation/shipment (the ICC sticker is applied to the product), while locally manufactured products obtain a Philippine Standard (PS) Quality and/or Safety Certification Mark licence. The applicant must be an in-country entity — a Philippine-registered importer of record (for ICC) or local manufacturer (for PS); a foreign manufacturer cannot hold the clearance directly. The technical file supporting ICC / PS includes safety test reports to the applicable PNS IEC standards (PNS IEC 60598 luminaires, PNS IEC 62560 self-ballasted lamps), performance/energy evidence for the DOE label, and EMC where in scope. Test reports should come from a BPS-recognised (ILAC MRA / ISO IEC 17025) laboratory. Customs release of covered products is conditioned on a valid ICC.BPS Import Commodity Clearance (ICC) scheme — per-shipment clearance for imported covered products (BPS / DTI) BPS Philippine Standard (PS) Quality / Safety Certification Mark — licence for locally manufactured covered products (BPS / DTI) |
The Philippine ICC / PS scheme differs from China CCC in both applicant model and process: (1) a foreign manufacturer cannot hold the Philippine clearance directly — it needs a Philippine-registered importer of record (ICC) or a local manufacturing entity (PS), whereas CCC is held by the producer; (2) ICC is generally per-importation/shipment with the ICC sticker applied to the product, a different cadence from a one-time CCC certificate; (3) test reports must support the BPS file to the applicable PNS IEC standards (PNS IEC 60598 / 62560) from a BPS-recognised laboratory — China CCC reports are not automatically accepted; (4) customs release of covered products depends on a valid ICC. The two schemes are parallel and non-mutual, so a separate Philippine technical file, in-country importer arrangement, and BPS clearance are required regardless of existing CCC status.[INFORMATIONAL] Market access for covered LED lamps and luminaires in the Philippines runs through the BPS ICC (per-shipment, for imports) or PS mark (for local manufacture), held by a Philippine in-country importer of record or local manufacturer — a foreign manufacturer cannot hold it directly. This differs from China CCC, which the producer holds directly, and the two are parallel and non-mutual. Test reports to PNS IEC 60598 / 62560 from a BPS-recognised laboratory must support the BPS file, and customs release of covered products depends on a valid ICC. A separate Philippine technical file and importer arrangement are required regardless of CCC status. | Bureau of Philippine Standards (BPS), Department of Trade and Industry (DTI)2026-06-15 · reference |
| Electrical Safety — General Luminaire (BPS ICC / PS + PNS IEC 60598) | China's general luminaire safety standard is GB/T 7000.1-2023 (Luminaires — Part 1: General requirements and tests), which replaces GB 7000.1-2015 from 1 January 2026 and changes the designation from mandatory GB to recommended GB/T; CCC obligations for in-scope luminaires remain governed by the applicable CNCA rules. CCC testing is by CNCA-authorised laboratories at the China 220 V 50 Hz supply. Both PNS IEC 60598 and GB/T 7000.1 share the IEC 60598 base, but the conformity process, supply reference (230 V 60 Hz vs 220 V 50 Hz), documentation, and clearance are separate from the Philippine BPS scheme.GB/T 7000.1-2023 — Luminaires — Part 1: General requirements and tests (replaces GB 7000.1-2015 from 1 January 2026; recommended GB/T designation) CNCA-C10-01 — CCC certification rules for luminaires |
LED luminaires placed on the Philippine market and covered by the lighting technical regulation must demonstrate electrical safety to the Philippine National Standard adoption of IEC 60598 (PNS IEC 60598-1 General requirements and tests, with the relevant Part 2 sections for the luminaire type). Key requirements cover protection against electric shock, insulation and dielectric strength, creepage and clearance distances, thermal endurance, mechanical strength, and wiring terminals — evaluated for the Philippine 230 V 60 Hz supply. Safety is demonstrated within the BPS conformity scheme: an Import Commodity Clearance (ICC) for imports or a PS Certification Mark for local manufacture, supported by test reports from a BPS-recognised (ILAC MRA / ISO IEC 17025) laboratory. The rating plate and product markings must follow PNS IEC 60598 and Philippine requirements, and a valid ICC conditions customs release.PNS IEC 60598-1 — Luminaires — Part 1: General requirements and tests (as adopted by BPS), with applicable Part 2 sections BPS Import Commodity Clearance (ICC) / Philippine Standard (PS) Certification Mark — lighting technical regulation |
PNS IEC 60598 and GB/T 7000.1 share the IEC 60598 technical base, so much of the safety evaluation overlaps, but the gaps are procedural and supply-related: (1) safety must be demonstrated for the Philippine 230 V 60 Hz supply, not the China 220 V 50 Hz basis, and creepage/clearance and dielectric assumptions should be confirmed at the higher nominal voltage; (2) the test report must support the BPS ICC / PS file from a BPS-recognised laboratory — a China CCC report under GB/T 7000.1 is not automatically accepted; (3) the clearance must be held by a Philippine in-country importer (ICC) or local manufacturer (PS); (4) rating-plate markings and instructions must meet PNS IEC 60598 and Philippine expectations. Existing China test data may shorten testing but cannot be directly reused for the Philippine clearance.[INFORMATIONAL] Electrical safety for LED luminaires in the Philippines is demonstrated to PNS IEC 60598 within the BPS ICC / PS scheme and evaluated for the 230 V 60 Hz supply. The technical base overlaps with China GB/T 7000.1 (both IEC 60598-derived), but a China CCC report is not automatically accepted, the supply reference differs (230 V 60 Hz vs 220 V 50 Hz), and the clearance must be held by a Philippine in-country importer (ICC) or local manufacturer (PS). Test to PNS IEC 60598 at a BPS-recognised laboratory and confirm creepage/clearance at the higher nominal voltage before market entry. | Bureau of Philippine Standards (BPS), Department of Trade and Industry (DTI)2026-06-15 · reference |
| Self-Ballasted LED Lamp / Driver Safety (PNS IEC 62560 + control gear) | China's equivalents are GB/T 24906 / GB 24906 (Self-ballasted LED lamps for general lighting services with supply voltages above 50 V — Safety specifications, aligned with IEC 62560) for retrofit LED bulbs, and GB 19510.14-2014 (control gear for LED modules, aligned with IEC 61347-2-13) for LED drivers. CCC may apply to certain self-ballasted lamps and drivers in defined ranges, tested at CNCA-authorised laboratories at the China 220 V 50 Hz supply. The Chinese GB-based reports are not automatically accepted in the Philippine BPS conformity scheme.GB/T 24906 / GB 24906 — Self-ballasted LED lamps for general lighting services with supply voltages above 50 V — Safety specifications (China, aligned with IEC 62560) GB 19510.14-2014 — Control gear for lamps — Particular requirements for electronic controlgear for LED modules (China, aligned with IEC 61347-2-13) |
Self-ballasted LED lamps for general lighting (the screw/bayonet retrofit LED bulbs) placed on the Philippine market must demonstrate safety to the Philippine National Standard adoption of IEC 62560 (PNS IEC 62560 — Self-ballasted LED lamps for general lighting services with supply voltages above 50 V — Safety specifications). Requirements cover marking, interchangeability, protection against electric shock, insulation resistance and dielectric strength, mechanical strength, fault conditions, and thermal/resistance to heat and fire — evaluated at the Philippine 230 V 60 Hz supply. For luminaires with separate LED drivers/control gear, the control-gear safety is assessed to the applicable IEC 61347 series (as adopted) as part of the technical file. Safety evidence supports the BPS ICC (imports) or PS mark (local manufacture), with test reports from a BPS-recognised (ILAC MRA / ISO IEC 17025) laboratory.PNS IEC 62560 — Self-ballasted LED lamps for general lighting services with supply voltages above 50 V — Safety specifications (as adopted by BPS) IEC 61347 series (e.g. IEC 61347-2-13) — Lamp control gear safety for LED modules (as adopted, for separate drivers / control gear) |
PNS IEC 62560 and the Chinese GB 24906 share the IEC 62560 base (as do the control-gear standards via IEC 61347-2-13), so the technical evaluation largely overlaps, but the gaps are procedural and supply-related: (1) safety must be shown for the Philippine 230 V 60 Hz supply, not 220 V 50 Hz — insulation, dielectric, and thermal assumptions should be confirmed at the higher nominal voltage; (2) the test report must support the BPS ICC / PS file from a BPS-recognised laboratory — China CCC reports are not automatically accepted; (3) where a luminaire uses a separate driver, both the lamp/luminaire and the control gear must be covered in the technical file; (4) markings and instructions must meet the Philippine requirements. As with the general luminaire case, China test data may reduce re-testing scope but cannot be directly transferred to the Philippine clearance.[INFORMATIONAL] Self-ballasted LED lamps for the Philippine market must demonstrate safety to PNS IEC 62560 (with separate drivers assessed to the applicable IEC 61347 series) within the BPS ICC / PS scheme, evaluated at 230 V 60 Hz. The base overlaps with China GB 24906 / GB 19510.14 (both IEC-derived), but China CCC reports are not automatically accepted, the supply reference differs, and the clearance must be held by a Philippine in-country importer (ICC) or local manufacturer (PS). Confirm insulation, dielectric, and thermal performance at the higher nominal voltage and test at a BPS-recognised laboratory before market entry. | Bureau of Philippine Standards (BPS), Department of Trade and Industry (DTI)2026-06-15 · reference |
E-E-A-T
Named editorial review
Pending named reviewer
Official regulator, standards body, notified body, customs, or primary legal source preferred. Local PDFs are not accepted.
Editorial controlsRows must include publisher, official URL, access date, verification flag, and last_verified before human_reviewed can be true.
SOURCES
Official-source register.
- Department of Energy (DOE), Republic of the Philippines · accessed 2026-06-15 · reference · used in 1 rows
- Department of Energy (DOE), Republic of the Philippines · accessed 2026-06-15 · reference · used in 1 rows
- Bureau of Philippine Standards (BPS), Department of Trade and Industry (DTI) · accessed 2026-06-15 · reference · used in 6 rows
- National Telecommunications Commission (NTC), Republic of the Philippines · accessed 2026-06-15 · reference · used in 1 rows
- Environmental Management Bureau (EMB), Department of Environment and Natural Resources (DENR), Philippines · accessed 2026-06-15 · reference · used in 2 rows